Hello Vanderfolks, I just had the form rollers on my No. 4 recovered. A very nice gentleman from RotaDyne came to my house to pick up the old ones. He took the whole assembly with him, and they shipped everything back disassembled. I’ve looked through the archives for instructions on putting things back together, but […]
MoreCategory: Inking System
SP 20 handle problem
I am trying to figure out how to tighten the action on the CM-37 handle of the inking system. This press has always had problems with uneven inking and after eliminating trip mechanism issues and replacing glazed rollers, ink distribution on the form is still occasionally lighter on the operating side. I think it has […]
MoreInk Migration Problem
The research and development division of NA Graphics has taken up the challenge of figuring out why ink migrates from one side to the other on Vandercook inking assemblies. To that end, we are working in conjunction with Dave Seat, who is in residence this week in our main research facility here in Silverton, to […]
MoreUni I roller squeal
I am having an issue with our Uni I—it has a squeaky rider roller. I took a look at an old post, ‘Inking Roller Squeal,’ and that was helpful, but I have an additional question. The black knob at the end of the rider is loose, but when it is held in place, the squealing […]
MoreModel 25 inking carriage
NEW CONTENT AT BOTTOM The problem I am having is that I can not see how to remove the distributor frame. It is wider than the frame which holds the mechanism to raise and lower the roller assembly. I can raise the distributor frame about 1/2 to 3/4″, but since it is partially in front […]
MoreChallenge 21MP Vibrator Assembly Issues
Hi Folks – I know that I use one of the “knock offs”, a Challenge 21MP (similar to the Vandy SP15), but I’m up poop creek without a plunger. I am calling on the collective wisdom of this group…. I’ve been restoring this press (some rust – lots of gunk) and have run into a […]
MoreMigrating ink
The Book Arts Program at the J. Willard Marriott Library, The University of Utah has a Vandercook 15-21 (shown with the top frame assembly removed) that is experiencing difficulties. Within minutes of application, a majority of the ink added migrates to the non-operator side (highlighted in the image) of the ink distributor assembly and form […]
More#4 form roller gear rack
I have been perusing the posts related to #4 form roller problems, specifically in regards to the clutch plate. I finally got a good handle on the source of all the racket that my press has been making for the last few months by adjusting the roller assembly and shimming the clutch plate. The issue […]
MoreUni I Bullet Catch?
Can anyone provide a picture and approximate dimensions of the bullet catch that holds up the ink distribution rollers for cleaning on a Uni I? Ours has gone a-miss and I have a VERY KIND friend willing to machine us a new one–but I have no idea what it looks like!
MoreI, too, am having roller problems on my SP-15
Rather suddenly my rollers decided to crap out by not inking the form evenly. I am using photopolymer plates. The Problem Form is not being inked evenly. Ink is heaviest at the beginning of the form (the area the form rollers hit first). Based on the image above, it appears that the rollers are not […]
MoreSP-15 ink drum gear broken
Hi there — This is my first post. I have an SP-15 (serial #26151), and I looked through my manual, but am still unsure of the part names. It appears the gear on my motorized roller is broken. This is the gear that the belt / pulley (?) runs on to actually move the roller. […]
MoreVandercook 4 repairing clutch plate
A prelude leading up to a repair question- I am restoring a Vandercook 4, serial # 10877, that I’ve had for a few years now. I’ve been mostly removing accumulated layers of ink, grease/dust and mild rust, and lubricating moving parts. With a couple of exceptions nearly everything appears in order. One of the first […]
More