Hello again! So in the process of getting back in the saddle I also noticed another quirk on my Universal III. I’m not sure if it is a problem per se or if the problem is just me… I noticed that all the prints I have been pulling are consistently cocked out of square a […]
MoreCategory: *Model
Looking for advice. Part 1: Uni III(ab) form roller tilted
I have recently begun to produce work on my Uni III after a long hiatus, and have run into a couple of vexing issues. Firstly, I realized that the rear form roller was laying down ink only on the side opposite from operator. The roller will not adjust low enough on the operator side (the […]
MoreUniversal III form roller gear issue (again!)
I’ve had this issue before and I can’t remember how I fixed it. When I started printing today, there is this noise that is coming from (I believe) from the rear form roller gear not being in the correct position on the core. You can hear it just as the cylinder leaves the feed board. […]
MoreDesperately seeking a solution to a mystery (Cylinder Jamming)
I have a Vandercook 219. Not sure but I think NS (1957). It prints like a dream, or did until this afternoon. The rolling cylinder suddenly started to hang up about 3 inches into the forme. So the first few inches of the forme prints, but then the cylinder meets profound resistance, as if something […]
MoreUniversal III Form Roller gears
I’ll say that the form Roller gear is slipping off the track. I notice it’s when the vibrating roller shifts to the near side mostly. The only thing I have noticed is the first form Roller L shaped hinge is loose turning and has to be checked and turned back. There doesn’t seem to be […]
MoreSP-15 Manual Inking Crank Knob
I recently helped someone with his SP-15. One of his problems was that one of the roller height adjustment knobs had broken due to an impact. His press had knobs of solid plastic, sort of pear-shaped with a tapered stem. I installed a replacement knob which was round with a brass threaded insert. He also […]
MoreMystery adjustment mechanism on VANDERCOOK 219
I am wondering what these two screw adjustments are for: The first is the square assembly near the inking plate with three screws, but then behind it recessed into the bed is a hex screw. I can’t find reference in the manual to them, but I could easily be missing it.
MoreDrifting Deadline on a 320
Hello all, I’ve just begun to teach at shop with a 320 that has a deadline that as of right now is a solid 2 inches past the original scribe line. I know that its not unheard of to have up to 3 picas off the original, but this seems excessive! Previous instructors and students […]
MoreNo. 4 Print/Trip Assembly
I just started working with a friend’s No. 4 press. It prints great and seems like a really solid machine. The machinery used to lower the impression cylinder from trip to print during the print stroke then back up to trip for the return to the feed table seems very different compared to the SP […]
MoreUpdate on 15-21 rail issues
I haven’t checked in on the Vanderblog for a long time but wanted to say I had my rails milled at a reliable machine shop in Holyoke, MA, that works on a lot of old press equipment. I removed the bed and transported it to them, they milled the rails on both sides to my […]
MoreSP-15 Motor / Ink Drum Noise
We are having some issues on our SP-15 with a “clicking” noise from the ink drum. It sounds like it’s coming from the pulley/timing belt area. It’s gotten progressively worst the past 2 days and also looks like it’s maybe a little lopsided (or is that just the belt?). This press is still new to […]
MoreNo. 3 stationary lock up bar?
I am going to be a new owner of a No. 3. that doesn’t have a lock up bar. I am considering having a metal worker create stationary “foot lock up bar” (I think that is what the manual is calling it). I have seen the post linked below about the fixed dead bar for […]
More