I was running some small posters yesterday on my Uni I AB. Things were going smoothly until the powered carriage was moving towards the end of the bed and got stuck midway. It just stopped. I run it pretty slowly so it wasn’t a very sudden stop it just was rolling along and then wasn’t. […]
MoreCategory: *Model
SP-15 Form Roller Imbalance
Hello Vanderfriends, Would love some to get some thoughts on a roller issue. First I should mention that I am working with new rollers and a press that is new to me so I unfortunately don’t have a frame of reference for past performance. I’m experiencing an imbalance with noticeably heavier ink coverage on one […]
MoreUNI-1AB
Good Day Vanderbloggers, I have recently acquired a “fixer-upper” UNI-1 needing everything related to the inking on the press including the drum, oscillating roller, rider and assembly, the form roller blocks, levers etc. I am looking for a parts machine (long shot) or will begin to fab what I need. I have contacted the usual […]
MorePress inspector
press inspector’s name on my Uni II also showing the type height the press is machined for
MoreVandercook 099 Proofpress – Poor Impression
I just purchased a Vandercook 099 Proofpress (https://vandercookpress.info/vanderblog/timeline/2/#099). It is in great working condition and has been well taken care of. I have experience with a Vandercook press but not this one. I have to ink the plate by hand and then place the paper on the form (it did not come with the optional […]
MoreUniversal 1 AB Hand ink drum wobbly
Hi All, I read the posts in the Vanderblog archives about SP15 ink drums wobbling because of a broken plastic gear or shorn off screws. Is it the same fix or different on a Uni 1 AB? On our Uni 1 AB, while printing we noticed that the lower steel ink drum was not inking […]
MoreSP20 Oil Holes
I’m happy to say that I recently purchased my first vandercook SP20. I’ve worked on another vandercook but did not maintained it. This site has been extremely helpful with almost all the information I need, however I can not find the oil holes. Does anyone know how many oil holes are on this model and […]
MoreNew Rollers Slightly Different Diameters
Hi All, I just received two newly recovered rubber rollers for a #4, done by Rotadyne. I measured the rollers and one is bigger than the other in diameter by 1/32″. One roller is 2 1/2″ and one is 2 1/2 plus 1/32. I asked the roller company to make them 2.515″ in diameter. Should […]
MoreUniversal I AB – Power Carriage Fuse Problem
I’ve been working on a thorough clean-up of my Uni I which was very grimy and dirty. I’ve already tore down and cleaned the adjustable bed which was frozen. That went smoothly thanks to the fine documentation from previous posts. Currently, I am dealing with a problem of immediately blowing a fuse when I put […]
MoreFlickr set – Installing new form rollers on a Vandercook No. 4
Continued thanks to everyone who has the patience and takes the time to answer the many questions that we relatively new printers come up with. I recently asked for step-by-step instructions for installing new form rollers on my No. 4, and the replies I got were extremely helpful. I put together a Flickr set on […]
MoreVandercook 22
I picked up a 1960’s Vandercook 22 from the University of Massachusetts, Dartmouth. It had be sitting in storage for a very long time, but it is in excellent condition. It is a very strange machine, but will be useful for large jobs. The ink rollers (3) and the impression roller move in a continuous […]
MoreSP15 grippers and trip lever issue
Hello. I have a lovely little SP15 and this is my first mechanical issue I’ve experienced thus far. I hope someone can help me solve it… Yesterday, my grippers stopped working. In looking at the manual and the press, I see the gripper cams are not lined up with the gripper screws. I am not […]
More