In case anyone is interested and had not seen them. A no.1 http://www.ebay.com/itm/Vandercook-proof-press-No-1-stand-accessories-/320747732206?pt=LH_DefaultDomain_0&hash=item4aae0dfcee#ht_500wt_1297 And an SP-15 http://www.ebay.com/itm/Vandercook-SP-15-LETTERPRESS-proof-press-/110734059775?pt=LH_DefaultDomain_0&hash=item19c843a8ff#ht_9561wt_1282 I wonder what the going price will be on each.
MoreCategory: *Model
Vandercook 219os Form Roller Dimensions
I am in the process of getting a set of roller cores recovered for my 219 old style but need the dimensions to provide the company recovering them for me. Can anyone help me out or point me in the right direction? Thanks in advance!
MoreSP-15 Trip Spring Question
Yesterday when printing I noticed that the usual sound of the trip springs on my SP-15 seemed different/quieter. Upon examining, I found that the spring on the operator’s side is no longer fitting snugly under what is referred to as “Dowel B” on sheet #302 “SP Series Replacement Trip Spring” diagram that Paul has posted […]
MoreUni I – Power carriage stuck at feed board
I’ve been having some inconsistencies with the braking and starting of my Universal I. Dave Seat was here about a month and a half ago and made some adjustments to the microswitches to prevent the hard hitting at the feed board I was having (and more importantly showed me how to make proper adjustments). Yesterday […]
MoreVandercook 03 – Impression roller and bearings
I am wondering about the impression roller (I don’t know if this is the right name) on this press. I’ve noticed that mine is a bit damaged, with some traces of scoring. I am worried this might cause uneven impression. Is this a roller that can be recovered or is this not a replaceable part? I […]
MoreMotor – Universal I
Recently the motor on my universal I has been reluctant to start. If I manually give the cylinder [drum] some torque, it will start. I replaced the capacitor mounted on the motor ($6.00), which seemed to help some. I can get a new motor from a local supply house for a reasonable cost (approx. $150) but […]
MoreLooking for SP-15 roller cores
Hi everyone. First post here. I am looking for at least one SP-15 roller core. If anyone has any to spare that would like to sell, please let me know. Thank you very much in advance.
MoreLubricant for 05 impression cylinder shaft bearing?
Quoting from sheet 108 of the sparse Vandercook 05 proof press manual sheets: – SAE 20 motor oil is recommended for all moving parts. – Ball bearings X-2688 and X-2698 are packed in grease and require no further attention. I’ve not had a chance to disassemble and investigate the carriage assembly thoroughly enough to get […]
MoreSticky, tight, rider roller on 4T
I had the wooden bearings in the rider roller of my 4T replaced a couple months ago after the old ones disintegrated. Everything was working fine until recently when I noticed that every time I drop my rollers to ink up (with the motor turned on) the top frame assembly begins squeaking and then slows […]
MoreAdvice on purchasing
First post! I am looking to purchase a Vandercook and needed some advice. I am basically looking to get one that has at least a 14″ x 20″ if not larger working form. In good condition and wanted to know some modal numbers to consider. Also, what price range would it run for? I will […]
MoreSP20 Slurring
I’m at wits end trying to figure out why I’m getting slurring problems on my SP20. I’m using photopolymer plates from Boxcar on a patmag base. Everything calipers out correctly to .918, including my roller height gauge. I’ve adjusted the rollers and measured them in several places on the bed. I have brand new rollers […]
MoreVandercook 320G packing
Hi everyone! I’m hoping someone out there may be able to offer me some advice with packing my Vandercook 320G. I’ve got a piece of cold rolled steel, 18 gauge/.050″ to make up for the galley depth. I talked to a few print shops in my area about packing, and one printer I talked to […]
More