Hi all, I’m the new caretaker of an SP 20 (serial 23442). I’ve been investigating a carriage jam issue and have found that the trip assembly on the non-operator side of the carriage (X-21755) is sitting much lower than on the operator side. Because of this, the rogue trip arm has been scraping against the […]
MoreCategory: *Model
Chain Problem on Universal III
I just acquired a nice Universal III which I’ve been cleaning up. I started up the motor today and after about a minute, it stopped, although it was still humming. I shut everything down and pulled off various covers and have isolated the problem to the chain. It’s stuck in the gear that sits BELOW […]
MoreUni III roller bearer issue?
Looks like when new rollers were put on the press, two of the roller height adjustment mechanisms were put on backward, so that the locking nut faces the wrong way. I assume they should face inward, but we have two that face outward. Anyway, a few days ago, one of the rings came off the […]
MoreUniversal I PAB | Control Station Panel Replacement
Howdy. I trust you and yours are well. I recently did some electrical work (thank you Fritz, Daniel, Paul, Steve, John, and Max) on my Universal and I am replacing the Control Station panel. Would anyone like one while I am at it? This will be a laser-engraved, silver substrate revealing a black core to […]
MoreBlack #4
Came across a nice #4 but it is black Do you know if Vandercook made black ones? Norman Hicks +1 415-725-1670
MoreVandercook 2 Hand Proof Press lockup bar
Hello all, I have a Vandercook 2 in need of some sort of lockup or dead bar. I don’t know if this type of press came with one originally. Even if it didn’t, I’d appreciate guidance on how to specify one for a fabricator (or do it myself). Thanks for your help!
MoreMystery assembly adjustment on Vandercook 320
I’m fixing up a filthy Vandercook 320 press, and I’ve just been cleaning up the carrier mechanism for the form rollers. I stripped everything off the carriage including the LN-19 Ink Frame Brackets (one on each side). The parts have been cleaned and now it’s time to reassemble things. Reattaching the LN-19’s leaves me with […]
MoreVandercook 219 front “table”
I’m looking for the front “table” part of a Vanderdcook 219 and I thought someone on these boards might have that part or know where to look for it. The press I am receiving is missing the cast iron supports and the “table” that sit at the far right of the press at the end […]
MoreVandercook 219 Trip lever assembly
Vandercook 219 New Style infrequently does not stay in trip mode on return to feed board, the operator must very slowly return the cylinder to the feedboard. Examining the ‘Cylinder Carriage’ spec sheet on the owner’s manual suggests that the ‘ (X-2884) Connecting Rod Assembly’ with its 8 ‘(X-3602) set screw(s) with lock washer and […]
MoreVandercook 325 A removing Auto Paper Feed
May I get your thoughts on removing the auto paper feed feature on my newly acquired Vandercook 325 A. It is fully operational, with no missing parts. I will be printing multi-color woodcut posters on it. It seems to me at this early stage to be a whole lot of fuss for not enough gain. […]
MoreSP15 issue – uneven inking along length of bed
Not sure why I always run into issues when on deadlines… Having an issue where I get an impression but there just isn’t any ink on the form and would love to hear any thoughts on what the problem/solution might be. The uneven inking is happening for the length of the press bed. Was printing […]
MoreUni 1 form roller gear run out
Now that the carriage bounce is sorted out thanks to Paul and Ray, the next item is the crazy wobble in the form roller gear. I tried to attach a video to this post but failed somehow. The video here shows how bad it is. The set screw and split sleeve are present in the […]
More