I own a Uni III PC AB with a Reliance motor. I wanted to check the oil in the inking motor as there is a bit or a burning smell after a long day printing, and I assume the oil in this decades old machine has never been changed. Thus, it seemed appropriate to replace […]
MoreMore TagCategory: *Model
Impression rollers and carriage ball bearings
My 15-21 has a history of the carriage rollers and ball bearings seizing up now and then. This makes moving the carriage very difficult and printing impossible. The last attempt I made to loosen them up involved a vacuum jar and motor oil. The grease inside the bearings was dry and (let’s just say…) “crunchy”. […]
MoreMore TagVandercook No.4 Piece Fell Off
Hello! I’ve been trying to identify what this part is that fell off the press and find the home to reinstall it on the press. It was found on the right side of the press when looking up towards the feedboard side. I have a Vandercook No.4. Any direction you could provide would be great, […]
MoreMore TagVandercook #4
Hi Paul. We’ve just purchased a Vandercook #4 we think it was originally owned by University of MN Duluth, serial #9903. We removed the carriage for transportation and will be following your directions for reassembly! While it is off we’ve been getting her all cleaned up and noticed that three of the steel carriage rollers […]
MoreMore TagSP-15 Squeal
Got a bad squeal on the SP-15. Can’t figure out where the noise is coming from. Suspect that the back roller core is defective and the bearer is not holding it correctly. I think we need a new roller/core. Anyway, in printing the oscillating roller squeals badly. Just started doing this today. Any thoughts? Thanks.
MoreMore TagRoller issues, squeaky sound on No.4
Revised. I’ve recently refurbished a No. 4. When the roller carriage is in contact with the ink drum (hence the form roller clutch is engaged), there’s an awful squeaking sound. The front rider roller does roll, and the oscillating roller seems sort of sluggish. It’s difficult to gauge where the sound is coming from, but […]
MoreMore TagSP25 ink drum “bouncing”
The ink drum on my SP25 has started bouncing up and down at one end as soon as any slight pressure is applied, like when I lower the form rollers or when I wipe off the ink while the drum is turning. I can’t see any visible irregularities in the chain links or any of […]
MoreMore TagVandercook Universal 111 for sale
We have this machine available, plus two other Universal 111’s. Main one was used up to about a year ago, another was for spares and the third was used as a cutting die station. I would like all three to go together to a good home and I am happy to discuss offers and assist […]
MoreMore TagVandercook 4 Blunder
Hi all – I’m in the last stages of cleaning up my Vandercook and I did what I told myself I never would. I ended up with 4 bolts and 8 washers that I cannot for the life of me figure out where they go. I’ve looked over the press and also the schematics and […]
MoreMore TagVandercook 1 Cylinder Removal
Hi, I have a Vandercook 1 single truss proof press, and the cylinder assembly was taken off for moving. I am wondering how to reattach and time it? Steven
MoreMore TagInstalling New Rollers — Clutch Pin Issue
While installing new rollers on the #4, I ran into an issue where the threaded pin (MR-109) won’t pass through the new clutch pin (MR-110) once in the roller. Separately, all the parts fit together just fine. Once on the roller core, the threaded pin will pass through the holes in the clutch block (MR-108), […]
MoreMore TagVandercook SP-20 / SP-25 Inking System Improvement From NA Graphics
New IMPROVED Form Roller Block Kit for the SP-20 / SP-25 inking system. Fritz of NA Graphics has designed and had manufactured NEW SOLID Form Roller Supports and Bearing Block Assemblies for the SP-20 and SP-25 Vandercook’s. On the fourth of July 2019 Dave and Beth Seat installed the first of these NEW inking system […]
MoreMore Tag