Hello, this is Britt at Banshee Press in Denver. I am having a problem with my Vandercook Model UNI-I, Serial # 24389 with auto carriage. On the trip cycle, the carriage balks with an abrupt jerk – sometimes to the point of stopping – at 21 1/2″ measured from the feed-board end of the press. (It […]
MoreFerdinand Wesel
Ferdinand Wesel (1846-1912) was the founder of the F. Wesel Manufacturing Company, which among other equipment, made some of the first flatbed cylinder proof presses. Born in Frankfurt A.M., he learned the printing-machinery trade, as The Inland Printer once put it, “in the thorough manner characteristic of his countrymen.” In 1866, he emigrated to New York and […]
MoreOrigin of the modern proof press reconsidered, Part II
In a 2010 post, I examined Vandercook’s claim to be “the originators of the modern proof press.” In it I discussed presses shown in a 1906 catalog issued by the British manufacturer Harrild & Sons (courtesy of Steven O. Saxe). In the comments, Eric Holub shared images from a 1904 catalog for Soldan’s, another British firm. Here’s another contender thanks again to Steve Saxe, with whom […]
MoreSP20 form roller issues
Recently when inking the rollers on my Vandercook SP20 I have encountered the following problems. 1) When I apply ink across the distributor roller and let it down on the form rollers the ink does not spread evenly and there seems to be some hesitation in the distributor rollers. 2) When I roll the rollers […]
MoreVandercook No. 2 Proof Press – For Sale – $900
I purchased this press when I was making woodblock prints 13+ years ago. I had a dream of refinishing it and properly setting it up. However that dream has since long passed, but perhaps that’s your dream now. If so, let’s talk. Pickup or arranged shipping would have to be from Morton, IL 61550. $900 […]
MoreVandercook SP20 Ink Drum Not Spinning
Though the ink drum drive chain and gear seem to be operating normally when powered on, the ink drum itself is not spinning. The ink drum does move freely when manually manipulated.
MoreQuick Roller Diameter Gauge
Our friend Kevin Martin at the Papertrail, in New Dundee, Ontario, Canada, has developed an ingenious flexible roller diameter gauge. It’s available as a free pdf on his website.
MoreReattach Bottom Roller Assembly to Lift Arm on No. 3
Hello all, here’s another question for a No. 3. I got brand new rollers and have secured them into the bottom roller assembly, but now I need to put the assembly back onto the lift arm bracket and want to make sure I’m doing it correctly. Any tips on how this should go? I have […]
MoreRoller Height Differences along Length of Bed?
I’m still running into problems on my No.3 with respect to roller height and I haven’t seen anyone else having this issue. I’m using a type-high gauge (from NA Graphics) on top of a cold-rolled steel 18-gauge plate. I set the proper roller height where the start of my Boxcar Base would be, then roll toward […]
MoreVandercook No 4 gripper foot pedal problem
We have a No. 4 (S/N 8655) and have a problem with the foot pedal mechanism that interacts with the gripper trip assembly. The foot pedal is connected to the pivot mechanism on the non-operator side of the press by way of the bicycle chain on the outside of the press cabinet. I had the […]
MoreHow do you print with gold paste?
I have old cans of VanSon Holiday gold paste and a can of gold paste from Cal/Ink. How do you print with these? Do you mix them with varnish or transparent base? Thanks.
MoreUniversal 1 home/start position
Hi Folks, Sorry if this has been covered before… Haven’t printed on this machine yet, but in the course of general lube and clean-up, I detect one issue: in the home/start position, the carriage doesn’t quite sit well-settled to the left/feedboard. it wants to roll off of the correct home/detente position and almost begin travel. […]
More