Hello Everyone, This is my first post here, so I ask that you bear with me if I say something obvious or written about previously. I have two adjustment questions. The first involves the inker base, image below. It seems to be at a pretty severe angle to me. Is there an adjustment for this? […]
MoreInk monitor
Hello, I have been trying to find info on the ink monitors for universal III presses. I have three in various states of repair.I would like to get one of them working. does anybody have knowledge of how they work and how to test.I just want something to play with during long runs to stave […]
MoreUni III – Gripper Problem at End of Bed
Hi – I have my (early) Universal III up and running and it’s printing very well and all is great except for the paper release/gripper problem at the end of the bed. I posted on this awhile ago and have been tinkering with the problem on and off ever since and still no luck. I […]
MoreUpdating wiring to add ground
I want to share my recent experience updating the wiring on an SP-20 motor to add ground. (Disclaimer: I am not an electrician although I consulted with an electrician.) My press arrived with the power cord cut off where it exited the press. So, I needed to add a plug anyway and decided it would […]
MoreSP-20 No Impression
I’m working on the rebuild of my (previously) dismantled SP-20 and I’m finally ready to test the impression. After calculating the correct amount of packing for a .019″ sheet (.024) on a cylinder with an undercut of 040 I proceeded to attempt a blind proof. There was nothing, not even when I added another .006 […]
MoreVandercook #17 Composing Room Cylinder $4000
Vandercook #17 17×25 printing area This press is functionally complete other than a missing side guide, I use a plastic clamp as a substitute. This press was built from several broken junk presses, I am moving onto a new project and need some room. This press saw weekly use in our shop until we replaced […]
MoreUniversal one in kit form
I recently bought a Uni 1 that was taken apart and painted gloss black. The cylinder is on. Who can help me get it back together. I would sell as is for $10,000 as is or $15,000 assembled with new rollers etc… Norman Hicks +1 415 725 1670 Hicks Frothers Printing Equipment, LLC
MoreVandercook #4 Bed Available
There is a cast iron bed for a Vandercook #4 available in Frenchtown, New Jersey. This bed is in good condition but has been completely stripped of parts. It does not include the cabinet or racks or any other bolt-on parts. No freight or shipping is available. If your press has damage or serious rail […]
MoreSP15 Ink Monitor
Hi, my SP 15 came with an ink monitor and I don’t know if it works. I wanted to know if it’s worth hooking it up or getting it fixed for better inking. I also wanted to know what the box inside the cabinet is for. Thanks.
MoreUniversal III – Gripper Bar Questions
As a result of a plumbing mishap a few weeks ago I have had to clean and re-lubricate the gripper bar on my Universal III AB. In the processes of doing this I’ve run into a few questions and potential problems, and I want to get clarification if I can before I do anything incorrectly. […]
MoreUniversal III Cylinder Rack – damaged screws / rocking
Hello everyone! Looking for some advice on how to proceed, I don’t want to do anything irresponsible here. I had a recent plumbing mishap above my in-home studio which deposited some light debris onto my Uni III AB. After a particularly thorough and careful cleaning of the press, I noticed some problems. In the process […]
MoreVandercook SP-20 Ink Distributor Roller Spring Replacement
This is for Fritz, who asked me to make a post here to place an order with NA Graphics. My spring on the ink distributor roller broke a bit ago. We spoke on the phone last week. Is this the best way to place that order for the SP-20 Ink Distributor Roller springs? I need […]
More